Tear Aid PATCH aerobed Airbed Air Bed MATTRESS WATERBED REPAIR 3x6 Type A OR B

Description

YOU PICK !!  Type A or Type B.  FREE SHIPPING.
In this sale you will get 1 repair Patch- 3'' x 6".
FREE SHIPPING !!!!
If you don't need 3"x6".  check out our other listing's for 3"x12"
Type A :  works on the following Materials: Canvas, Rubber, Neoprene, Nylon, Most Fabrics, Plastics, Sunbrella, Gortex, Polyethylene, Polypropylene, Polyurethane, Non-oiled Leather, Acrylics, Fiberglass, Aluminum, Polyester, Hypalon. Using Type A on any Vinyl Surface will fail after a period of time.
Type B:  works for Vinyl and Vinyl-Coated Materials.
Each TEAR-AID
®
repair patch is made from an exceptionally tough, matte finish, abrasion resistant, elastomer that resists puncture and tearing.  It is combined with an aggressive adhesive formulated for high bond strength to a variety of surfaces such as canvas, leather, rubber, nylon, most plastics, paints, aluminum, stainless steel, fiberglass, polyurethane, polyethylene, polypropylene, vinyl and vinyl coated.  TEAR-AID
®
Type A and TEAR-AID
®
Type B provide a simple and easy method of patching holes and tears, as well as an excellent protective film solution.
Step 1- Clean surface and dry
Step 2- Peel and press to adhere- no glues!
Step 3- Enjoy benefits of this Fabulous product instantly!
** Does not dry, shrink, peel off- this is not a temporary repair, but something that will last.
This product is extremely stretchable, resistant, and strong, unlike anything that sells in most stores.
TEAR-AID® Type A is for All But Vinyl .
TEAR-AID® Type B is for
VINYL
HOLDS AIR
under pressure even when stretched
HOLDS WATER
under pressure even when stretched
SEE-THRU PATCH
works with all colors
INSTANT ADHESION
with no sewing
CONFORMS
to irregular surfaces
WON'T TURN GUMMY
in high heat
UV RESISTANT
inhibits yellowing for years
CUTS EASILY
to any size with scissors
NO GLUE TUBES
no mess liquid adhesives to apply
ELASTIC PATCH
that won't pull off when stretched
INSTRUCTIONS
GENERAL TEARS
AND
HOLES
For best results apply to a clean, dry surface. Clean the surface to be repaired with an alcohol prep pad, or a 50/50 mixture of rubbing (isopropyl) alcohol and water.
Surface temperature of the materials to be repaired should be 50 F or warmer. Do not put repaired material into a washer or dryer.
Before proceeding make sure surface is dry, and you have the correct patch type for the kind of material you are repairing.  This is for VINYL repair only!
STEP 1
Cut patch to size with scissors allowing for the patch size to extend 1 inch beyond all edges of the tear. If using more than one patch, allow for patch sizes to overlap at least 1 inch. Trim square corners into rounded corners.
STEP 2.  Peel -
Carefully peel back ½ inch of paper liner. Tearing the paper liner while stretching the edge of the patch will help to separate the liner from the patch - especially when the patch has been cut into smaller sizes.
STEP 3.  Stick -
Position and anchor exposed ½ inch edge – allowing the patch to extend 1 inch beyond all edges of the tear. Slowly peel back the liner while carefully applying the patch over the tear – take care to avoid air bubbles. Rub all edges to seal. Rub entire patch aggressively. Follow Steps 1-3 on the back side of the repair if you have access to the back side. Repair is complete.
REPAIRING TEARS EXTENDING THROUGH AN OUTSIDE EDGE
Follow steps 1 thru 3 with the following adjustments:
CUT the patch size to extend a full 1 inch beyond the edge of the torn material.
Peel and Stick positioning the patch
leaving a 1 inch tab extended beyond the outside edge of the torn material.
STEP 4.  Turn the material over
so that the adhesive side of the tab is facing up.
STEP 5.  Position Reinforcement Filament
tightly against the outside edge of the material by sticking it to the patch tab. The filament should be perpendicular to the open end of the tear to create a tough solid edge.
STEP 6.  Fold Over
the patch’s 1 inch tab and rub to adhere to the backside of the material – sealing in the reinforcement filament.
STEP 7.  Apply Another Patch
to the backside of the patched tear (so that both sides of material are patched) Rub entire patch aggressively.
STEP 8.  Trim
excess line. Repair is complete.
Trim
(
80lb Test Fishing line is our suggested reinforcement filament line)
HEATING IS AN OPTION
AND
NORMALLY NOT NEEDED.
HEAT TO SPEED UP CURING TIME (OF VINYL-ONLY TYPE B)
Heat time will vary depending on size of patch and distance of the heat gun from patch Allow repair to cool before handling.
For Tear-Aid Vinyl-Only Type B - to transform the good initial bond to an extremely high bond that would otherwise take 24 hours of curing time - After the patch is applied to the tear, briefly heat using an industrial heat gun that is set at approximately 350 F.  As the adhesive hot melt occurs, the patch see-thru clarity may change and appear easier to see-thru. This is an indication of over heating and the heat should be removed.
IMPORTANT:
Type B
is at approximately 50% adhesion upon initial application
and 100% adhesion after twenty-four (24) hours.
Type B has a new, unique adhesive that resists the oils in vinyl
that cause other adhesives to soften and turn gummy in sunlight
Welcome to our eBay store!
To make your purchase as simple and easy as possible, please refer to the store policies listed below.
After winning an item in auction or completing a Buy It Now purchase, you have two check-out options:
Check-Out Now!
Click the
Pay Now button
at the top of this listing to immediately proceed with our checkout and payment process. Please note that the
Pay Now
button is ONLY available after winning an auction or completing a Buy It Now purchase.
Check-Out Later
If you do not choose to Check-Out now, you will be notified by eBay via e-mail that you are the winning bidder. There is no need to contact us to arrange payment. We will automatically send you an e-mail within three hours of an auction closing. Our message will contain a link to our simple and secure checkout system, where you will be able to quickly and conveniently pay for your purchase.
You may also continue purchasing additional items from our auctions or eBay store. You have
7
days from the end of the first purchase to add additional items to your order. Make sure all of your auctions have ended prior to checking out. All of your purchases will be consolidated into one checkout!
Payment
We accept the following forms of payment.
Sales Tax
For shipments to
Iowa
addresses, we are required by State law to collect
7 %
Sales Tax.
Shipping
Northern Auto Parts ships all domestic orders via UPS. The shipping charge is determined by your shipping method, package weight, and dimensions. If you purchase multiple items from us, we can combine your shipping cost to save you money. Also, just use the shipping and payments tab to calculate your shipping if purchasing more than one of the same item.
We are happy to ship items internationally. All duties, taxes, and import fees are the responsibility of the buyer. Please note that items shipped internationally take more days to arrive then domestic orders.
International Customers
: All duties, taxes, and import fees are the responsibility of the buyer.
Attention Australian Customers
: We will automatically upgrade any packages over
15 pounds
to UPS Expedited to Australia. This will give you better tracking and get you your package faster. Again, we will not charge you any extra for UPS Expediated to Australia on packages 15 pounds or greater. We get great rates from UPS to Australia, and we are happy to pass them on to our customers.
Returns
You can return your item within 30 days for a full refund minus the shipping cost. If there is any problem with your order, please contact us right away and we will help resolve the situation.
Customer Service
If you have any questions about this product, or any other product featured on our ebay site, you can "Ask Seller a Question". You can also call us at 1-800-831-0884.